Content: Three eccentric metal seal butterfly valve with high temperature, light operation, open and close without friction, closed with the torque transmission mechanism to compensate for increased sealing, improved butterfly valve sealing performance and extend the life of the advantages. But there are still structural problems. At present, as a component used to realize on-off and flow control of pipeline system, it has been widely used in many fields such as petroleum, chemical industry, metallurgy, hydropower and so on. In the known butterfly valve technology, the dense use of multi-seal structure, the sealing material is rubber, and so on. Due to the structural characteristics of the restrictions, do not meet the high temperature, high pressure and corrosion-resistant, anti-wear and other industries. A more advanced butterfly valve is a three-eccentric metal seal butterfly valve, the valve body and the valve seat as a single component, seat sealing surface layer surfacing temperature, corrosion resistant alloy material. Multi-layer soft stacked ring fixed to the valve plate, this butterfly valve compared with the traditional butterfly valve with high temperature, light operation, opening and closing without friction, closed with the torque of the transmission mechanism to compensate for increased sealing, improved butterfly valve The sealing performance and extend the service life of the advantages. Three Eccentric Metal Sealing Butterfly Valve Structural Features Three Eccentric Metal Sealing Butterfly valve disc rotation center (ie, the valve shaft center) and disc sealing surface to form a size A bias, and the body center line to form a B bias; valve body The sealing surface centerline forms an angular position with an angle of β with the valve seat centerline (ie, the valve body centerline). However, this butterfly valve in the course of the following problems still exist: First, the multi-layer hard and soft stacked ring is fixed to the valve plate, the valve normally open state when the medium seals Surface formation of positive erosion, sheet metal sandwich in the soft seal by the erosion, a direct impact on sealing performance. Second, by the structural conditions of the structure does not adapt to do the following DN200 valve, because the overall structure of the valve plate is too thick, large flow resistance. Third, due to the principle of three eccentric structure, the seal between the sealing surface of the valve plate and the valve seat is pressed against the valve seat by the torque of the transmission device. The positive flow state, the higher the media pressure seal squeeze tight. When the flow medium countercurrent media pressure increases with the pressure between the valve plate and valve seat unit pressure is less than the medium pressure, the seal began to leak. High-performance three eccentric two-way hard sealing butterfly valve, characterized in that: the seat ring seal by the soft T-ring multi-layer stainless steel sheet on both sides. The sealing surface of the valve plate and the valve seat is an oblique conical structure, and a temperature-resistant and corrosion-resistant alloy material is deposited on the oblique conical surface of the valve plate; the spring fixed between the adjusting ring plate and the adjusting bolt on the pressure plate is arranged together. This structure effectively compensates for the tolerance band between the sleeve and the valve body and the elastic deformation of the valve stem under the medium pressure and solves the sealing problem existing in the process of transporting the valve in the bidirectional interchangeable medium. The soft T-shaped multi-layer stainless steel sheet on both sides of the seal ring, with the advantages of both metal seal and soft seal, both in low temperature and high temperature conditions, have zero leakage of sealing performance. Experiments show that pool positive flow state (medium flow direction and disk rotation in the same direction), the sealing surface pressure is the torque of the actuator and the medium pressure on the role of the valve plate. Positive media pressure increases when the valve plate oblique cone surface and seat sealing surface squeeze the more tight, the better the sealing effect. In counter-current conditions, the seal between the valve plate and the valve seat presses the valve plate against the valve seat due to the moment of the drive. As the pressure of the reverse medium increases, the positive pressure between the valve plate and the valve seat is less than the pressure of the medium. The deformation stored by the spring of the adjusting ring after the load is absorbed can compensate for the tight pressure on the sealing surface of the valve plate and the valve seat Play a role in automatic compensation. Therefore, unlike the prior art, the utility model has the advantages that the soft and hard multi-layer sealing ring is mounted on the valve plate and is directly mounted on the valve body, and an adjusting ring is provided between the pressing plate and the valve seat which is a perfect bidirectional hard sealing method . It will replace gate valves, globe valves and ball valves.
There are two main materials used in manufacturing exterior door handles-plastic and metal.
Both materials come with different finishes, such as smooth black, textured, chrome and primed. Textured handles offer better grip even when wet, while smooth black and chrome blends with the color of your car. Primed handles are ready-to-paint pieces, which are perfect if you want to match your vehicle`s unique color.
These application-specific parts are made to look like and seemlessly replace exterior door handles, reinforcement brackets, and more.
- Stock Appearance: these replacement exterior door handles were specifically designed to look and function the same as the original handle on particular vehicles, and to match the original dimensions and specifications
- Great Value: OE quality at a lower price.
Exterior Door Handle for Chrysler
Exterior Door Handle for Chrysler
Exterior car door handles lets you access your car's cabin. without them, doors are hard to open. Exterior door handles come in various shapes and styles but the operation is generally the same; pulling the lever out releases the hook from the vehicle frame`s latch.
Here are some types of OE replacement exterior car door handles: pull up, pull out, and trigger.There are two main materials used in manufacturing exterior door handles-plastic and metal.
Both materials come with different finishes, such as smooth black, textured, chrome and primed. Textured handles offer better grip even when wet, while smooth black and chrome blends with the color of your car. Primed handles are ready-to-paint pieces, which are perfect if you want to match your vehicle`s unique color.
These application-specific parts are made to look like and seemlessly replace exterior door handles, reinforcement brackets, and more.
- Stock Appearance: these replacement exterior door handles were specifically designed to look and function the same as the original handle on particular vehicles, and to match the original dimensions and specifications
- Great Value: OE quality at a lower price.
Zhejiang Xingting Auto Parts Co., Ltd , https://www.xingtingautoparts.com