Suction vehicles and suction trucks need to learn to save fuel at high altitudes in the mountains

Sewage suction and suction trucks are driven in mountainous areas and highland areas. Because of the steep slopes and long elevations, the engine cooling systems of road suction trucks and suction trucks are easy to "open pots," and the power and economy of sewage suction trucks and suction trucks. The nature deteriorates and the driving safety factor decreases.

High altitude, thin air, and low oxygen content in mountainous and plateau regions, incomplete combustion of fuels, slow burning speeds, declining engine power, and rapid increase in fuel consumption. Mountainous and highland highways in China account for approximately 40 percent of the total national highway mileage. When driving a sewage suction truck or a suction truck driving in a mountainous area or a plateau area, effective measures must be taken to achieve the goal of fuel economy.

Sewage suction and suction truck prices

1) Reduce oil supply. In order to accommodate the reduction in the amount of intake air, the amount of fuel supplied must be reduced. Carburetor gasoline engine is generally used to reduce the height of the float chamber oil surface 2 ~ 3mm, a carburetor with a needle can be turned down.

2) Increase the ignition advance angle. In general elevation of 1000 meters, the ignition advance angle can be 2 degrees earlier than the original. When the gasoline engine is working at the plateau, the pressure at the end of the intake is low, and the cylinder pressure also decreases, making it less prone to knocking. In order to increase the engine power and reduce the fuel consumption of the sewage suction truck and the suction truck, the ignition advance angle may be increased appropriately. In general elevation of 1000m, the ignition advance angle can be 2° earlier than the original.

3) Appropriately increase spark plug clearance. In general, the roads with better vehicle conditions and sewage suction trucks , suction trucks, engine spark plug gap can increase about O.25 mm, and some of the poor state of the car can increase O.15 mm or so.

In order to improve the burning rate, make the fuel burn fully and reduce the generation of carbon deposit, the gap of the spark plug can be appropriately increased and the ignition voltage can be increased accordingly. Generally, the gap between the engine suction plug and the engine suction plug of the suction truck can be increased by about 0.25mm, and the condition of the vehicle can be increased by about 0.15mm.

4) Ensure that the coolant operates within normal temperature. The normal temperature of the engine cooling water is 80~90°C. It is necessary to use the shutters and insulation to adjust the engine water temperature in time. This is mainly because in the plateau area, the pressure is low, the boiling point of water is also low, and the cooling water in the cooling system is easy to boil. At the same time, due to the steep and long slope, the sewage suction truck and the suction truck are running at a low speed on the long slope. More time, more load, more prone to overheating; and in the next long slope, due to excessive cooling, water tank temperature is too low. Therefore, it is necessary to correctly control the engine temperature while driving, otherwise, fuel consumption will increase.

5) Adjust idle speed to the lowest stable state

The ramps in the mountains and plateaus are numerous and long, and there are more idle times. In order to save fuel, idle speed should be adjusted to the lowest steady state. For the carburetor gasoline engine, the mandatory idler fuel economy with good quality and stable fuel economy is selected. When the sewage suction truck and the suction truck are in the long slope, the fuel supply to the carburetor is stopped and the fuel consumption is reduced.

Full Hydraulic Open-air Integrated DTH Drilling Rig

This type is open-are intergrated DTH rig works with Air Compressor accords to the DTH machine different air pressure and air consumption,actually they're also named DTH Drilling Rig,it's used to different site such as ore quarry site drilling,mining site,rock drilling site,salt mine blasting site,gold ore and hematite ore site,copper ore plant construction,mineral one-stop service construction.

Moreover, one quality DTH drilling rig and reasonable spare parts as well as drilling bits requires a quality brand and reliable manufacturer,just as same as us due we're a leading manufacturer!

Separated Drilling Rig,Open-Air Integrated Rig,Ore Blasting Drilling Rig,Automatic Top Hammer Surface Drill Rig

Henan YikYui Prospecting Machinery Co., Ltd , https://www.yikyui-rig.com