Second, the main components of the flat knitting machine frame, needle board, square rail, faucet, flower board.
Third, the horizontal machine parts placement 1, rack: There are two hills, and two beams to connect the hill into a whole, it is a casting. The small parts installed on the rack are wrenches, wrench fixing screws, pin plate screws, and pin plate screw compression springs. 2. Needle plate: It is made of steel plate with considerable hardness. The parts on it have large pressing strips, small beading, needle, tofu block and fixing screws. 3. Guide rail: The guide rail is made of prayer piece or special steel. It is fastened to the frame with fixing screws. It is generally divided into two front and rear, which is the track for the nose to walk. There is also a yarn feeder guide rail above the rear rail. It is mainly used when the feeding yarn feeder is moved smoothly to the right or left or the yarn feeder is replaced. 4, the faucet: it is the heart of the flat knitting machine, the parts of the whole machine head are installed on it, its parts have front and rear faders, push hand coke balls and screws, push hand pressure plate (also called push hand slider), the slider is loaded Bearing. The front part of the faucet is fitted with a three-eye cover plate, the screw passing through the three eyes is a needle-drawn triangle pull rod, the screw in the center eye is called a live chicken heart rod screw, the pull rod well ring and the needle-triangular small wrench, the live chicken heart wrench, the nose The surface is marked with a scale plate, the scale plate is equipped with a small platen, and the screw at the center of the scale plate is called a two-headed screw. The lower end of the two screws is fastened on the big triangle, the center of the two screws is mounted with the pointer, and the pointer is filled with the ingot screws. The swing frame is installed behind the faucet. The swing frame is equipped with a swing rod and a shuttle rod. The rear part of the machine head is also equipped with a pin switch. The main part above the machine head is a flower board. 5, flower board: flower board is the center of the flat knitting machine, it has a bottom plate seat, all the triangles are installed on the bottom plate seat, the triangle on the flower board has a needle triangle, a chicken heart triangle (live chicken heart, chicken heart), herringbone Triangle, big triangle.
4. The resolution of the triangle number 1. The resolution of the needle triangle: There are four needle triangles, and its number point method is point counterclockwise. When operating, the nearest one is called the first one. No., point counterclockwise, respectively, is the No. 2, No. 3, No. 4 needle triangle.
Note: There is a small wrench on the inner triangle of the inner flower block, press the small wrench to close the needle triangle, and lift the small wrench to open the needle triangle. The pinning triangles on the outer block are respectively equipped with a pin switch, the push pin is closed, and the pull pin is opened. 2, the resolution of the big triangle number: there are four in the big triangle, its number point method is the same as the point method of the needle triangle, the big triangle No. 1 is also the nearest one by the right hand, the big triangle number usually refers to the ingot Screw point. 3, the heart of the triangle of the resolution: the heart triangle is also called the thimble triangle, the heart of the front flower plate triangle is divided into two upper and lower, the upper side is called live chicken heart. The bottom is called the chicken heart.
304 Stainless Steel Cut Wire Shot
Longlived 304 stainless steel Cut Wire Shot are all produced through German craftsmanship with bright, defect-free and pollution-free material. After strict processing like heat treating, wire drawing, electronic spiral cutting, passivation molding and other processes, our products are strictly in a accordance with German Spring Association standard VDFI8001, German industrial standards DIN8201 and American Aerospace Material Specification Standard. It is widely used for surface shot blasting, sand blasting and shot blasting of stainless steel parts, aluminum alloy die castings, and copper alloy parts. According to different composition, stainless steel is classfied several grades such as 304, 410, 430, 201 and 304 stainless steel cut wire shot is the most popular abrasive of them as its excellent performance. The composition of 304 stainless steeel is: C≤0.07, Cr 17.00-19.00, Ni 8.00-10.00, Mn ≤2, P≤0.035, S≤0.030, Si≤1.00. So you can check if 304 Stainless Steel Shot could meet your requirement.
304 Stainless Steel Cut Wire Shot,304 Cut Wire Stainless Steel Shot,Deburring Stainless Steel Cut Wire Shot,Stainless Steel Rounded Shot
Longlived Metal Products Co ., Ltd , https://www.tzlonglivedmetal.com